Question 1

Apex Seal Wear and Failure

Accepted Answer

Gradual loss of compression, reduced power output, difficulty starting (especially when hot), increased oil consumption, and eventually the engine won't sustain combustion. In catastrophic failure, a broken apex seal fragment can score the rotor housing surface, requiring housing replacement. The apex seals are the equivalent of piston rings, they maintain the gas-tight seal between the rotor faces and the epitrochoid-shaped housing. Every rotation, the apex seals sweep across the housing surface under spring tension and combustion pressure. Over tens of thousands of rotations, the seal material wears down. The rate of wear depends on lubrication (oil metering pump function and pre-mixing), operating temperature, combustion temperature, and carbon deposit buildup. Full engine strip and rebuild. The engine is removed, disassembled, and all seals (apex seals, side seals, corner seals, oil seals) are replaced. The rotor housings are inspected and resurfaced or replaced if scored. The rotors themselves are inspected for wear. A quality rebuild costs $2,500-4,000 for the 12A and includes all seals, bearings, and gaskets. The 10A is slightly less due to smaller components but parts are scarcer.

Question 2

Rotor Housing Scoring

Accepted Answer

Deep scratches or grooves in the chrome or Nikasil coating of the rotor housing inner surface. Reduces compression even with new apex seals. Visible during engine disassembly. Foreign material passing through the engine (debris from a failed apex seal, carbon chunks, detonation fragments), running the engine with inadequate lubrication, or severe overheating that warps the housing and allows metal-to-metal contact. Mild scoring can sometimes be polished out. Severe scoring requires rotor housing replacement. Used housings in good condition run $300-800 each. New housings (when available) are $600-1,200 each. The 12A uses two rotor housings.

Question 3

Oil Metering Pump Failure

Accepted Answer

The engine receives insufficient oil for apex seal lubrication. The apex seals run dry, wear accelerates dramatically, and catastrophic engine failure follows. There may be no warning, the engine simply starts losing compression faster than normal. The oil metering pump (OMP) is a mechanical pump driven by the eccentric shaft that injects metered quantities of engine oil onto the rotor housing surfaces. The pump can fail mechanically (worn internals, broken drive), the oil lines can crack or block, or the pump calibration can drift with age. Two approaches. Conservative: rebuild or replace the OMP, check all oil lines, and verify function. Cost: $200-400. Aggressive (and increasingly common): delete the OMP entirely and rely solely on pre-mixing two-stroke oil with the fuel at a 1:150 to 1:200 ratio. This provides more consistent lubrication and eliminates the OMP as a failure point. Many rotary specialists recommend premix-only operation.

Question 4

Coolant Seal (O-ring) Failure

Accepted Answer

Coolant leaks into the combustion chamber (white smoke from exhaust, coolant loss without external leak) or coolant leaks externally from the engine block mating surfaces. The engine overheats. The rubber O-rings that seal the coolant passages between the rotor housings and the side housings (end plates) harden and lose their sealing ability with age and heat cycling. This is an age-related failure, the O-rings eventually go regardless of maintenance. Engine must be disassembled to replace the O-rings. Since the engine is apart, a full seal kit and rebuild is standard practice. Cost: $2,500-4,000 including all seals.

Question 5

Carbon Buildup

Accepted Answer

Hard carbon deposits accumulate on the rotor faces, apex seal grooves, and exhaust ports. The deposits restrict apex seal movement in their grooves, causing the seals to stick and lose their spring tension against the housing. Compression drops, power decreases, and the engine runs rough. Short trips where the engine never reaches full operating temperature, low-rpm driving (the rotary needs revs to stay clean), and poor fuel quality all contribute to carbon buildup. The rotary engine is particularly susceptible because the combustion chamber shape and seal arrangement create areas where deposits accumulate. Prevention is key, drive the car hard regularly, use quality fuel, and keep the engine at operating temperature. For established deposits, an "Italian tune-up" (sustained high-rpm driving) can clear some buildup. Severe cases require engine disassembly and manual cleaning. Some owners use decarbonising additives, but these are controversial in the rotary community.

Question 6

Inner Guard Corrosion

Accepted Answer

The front inner guards corrode from trapped mud, moisture, and road debris. Rust perforates the inner guard panels, weakening the structural support for the front suspension mounts. The inner guard design traps debris and moisture in areas with poor drainage. Factory corrosion protection on 1970s Japanese cars was minimal. Decades of accumulated grime holds moisture against the metal. Mild surface rust: wire brush, rust converter, and protective coating. Perforation: cut and weld repair panels. No reproduction inner guards are available, all repair work is custom fabrication. Cost: $1,000-3,000 per side for professional fabrication and welding.

Question 7

Floor Pan Corrosion

Accepted Answer

The floor pans rust from underneath, often hidden by carpets and sound deadening. In severe cases, you can see the road through the floor. The floor provides structural rigidity to the unibody, perforated floors compromise the car's integrity. Underside exposure to road spray, moisture trapped under carpets and insulation, and inadequate factory undercoating. Cars that have been parked on grass or damp ground are particularly affected. Floor pan repair requires cutting out rusted sections and welding in new metal. This is a major job that requires the interior to be stripped. Cost: $2,000-5,000 depending on extent. Floor repair panels must be fabricated, there are no off-the-shelf replacements.

Question 8

Lower Quarter Panel Corrosion

Accepted Answer

Rust bubbles and perforation along the lower edges of the rear quarter panels. Paint may appear bubbled or lumpy, indicating filler over rust underneath. Water enters the quarter panel area through seams and drain holes, sits inside the double-skin panels, and corrodes from the inside out. The lower edges are the first to show because gravity draws moisture downward. Quarter panel replacement or repair. Genuine RX-3 quarter panels are extremely rare and command premium prices when they surface. Repair involves cutting out rusted metal, fabricating patches, and welding. Cost: $2,000-5,000 per side for quality repair work. A genuine quarter panel can cost $3,000-8,000 if you can find one.

Question 9

Windscreen Channel Corrosion

Accepted Answer

Rust develops in the channel where the windscreen sits, hidden by the windscreen rubber seal. Often only visible as small rust spots at the edges of the windscreen. The rust is invariably far worse once the windscreen is removed. Water wicks under the windscreen seal and sits in the channel. The seal prevents the moisture from evaporating. Over decades, this trapped moisture corrodes through the channel metal. Remove the windscreen, assess the damage, and repair. Minor rust: treat and seal. Major rust: fabricate and weld repair sections. Cost: $500-2,000 depending on severity, plus windscreen removal and refitting ($200-400).

Question 10

4-Speed Synchro Wear

Accepted Answer

Grinding or crunching when shifting, especially into second and third gears. The gearbox may pop out of gear under load. The standard 4-speed gearbox was designed for the RX-3's stock power output. Many RX-3s have been driven hard (or raced) for decades, wearing the synchro rings. Ported engines producing above-stock power accelerate gearbox wear. Aggressive shifting without rev-matching also contributes. Gearbox rebuild with new synchro rings and bearings. Cost: $1,500-2,500. Alternatively, a 5-speed conversion using a later Mazda gearbox is a popular and arguably superior solution. Cost for 5-speed conversion: $2,000-4,000 including gearbox, bellhousing adapter, and driveshaft modification.

Question 11

Gear Breakage

Accepted Answer

A gear tooth shears off, the gearbox locks up or grinds catastrophically, and metal fragments contaminate the gearbox oil. The factory gears were not designed for the power levels that many modified RX-3s produce. Repeated shock loading (aggressive launches, clutch dumps) fatigues the gear teeth. Gearbox replacement or complete rebuild with upgraded components. Cost: $2,000-4,000. This is a strong argument for the 5-speed conversion if the car is driven hard.

Question 12

Radiator Inadequacy

Accepted Answer

The engine runs hot, particularly in traffic or on hot days. The temperature gauge creeps up or the engine overheats. The factory radiator is 50+ years old and was designed for 1970s traffic conditions. Reduced coolant flow through corroded core tubes, blocked fins, and degraded end tanks all reduce cooling capacity. The rotary engine produces significant heat relative to its displacement. Replace with an aftermarket aluminium radiator. Multiple options available for the RX-3 from rotary specialists. Cost: $300-600 for a quality alloy radiator. This is one of the best value upgrades you can make.

Question 13

Thermostat and Water Pump

Accepted Answer

Overcooling (thermostat stuck open, engine never reaches proper operating temperature) or overheating (thermostat stuck closed, water pump failure). Age. The thermostat's wax element degrades, and the water pump seal and bearing wear. Replace both as preventive maintenance. Cost: $100-200 for thermostat and water pump.

Question 14

Points Ignition Wear (Early Cars)

Accepted Answer

Hard starting, misfiring, rough running, loss of power at high RPM. Points-based ignition systems require regular adjustment and replacement. The points wear, the condenser degrades, and timing drifts. Convert to electronic ignition. Multiple aftermarket systems are available. Cost: $200-400. This eliminates points maintenance entirely and improves reliability and performance. Most surviving RX-3s have already been converted.

Question 15

Wiring Harness Degradation

Accepted Answer

Intermittent electrical failures, blown fuses, non-functional accessories, or complete electrical failure. 50+ year old wiring insulation becomes brittle, cracks, and allows shorts. Rodent damage is common on stored cars. Previous owners' modifications may have added poorly routed aftermarket wiring. Repair individual circuits as needed, or rewire the entire car with a reproduction or custom harness. Cost: $200-500 for individual repairs, $1,000-2,500 for a complete rewire.

RX-7 (FD)

RX-7 (FD) known problems